That's right it's Tutorial Wednesday and has Kelly got a great one for you this week!! YAY!! Perfect for my daughter!!!
Well this time I created a nail care gift box that I think any lady would love to receive. I used the
Bath'n'Bubbles Gilly digi stamp from
Prairie Fairy Designs as it so appropriately depicts getting pampered. I was inspired to create this by
Laurie a fellow online creator. However, I had to change the dimensions to fit a 100ml or 3.38 oz. of nailpolish remover. Plus I added an extra flap in the box to add sturdiness to the box.
Rear view
Cut two pieces of cardstock 9" long and 6 3/4" wide. Then score pieces at 2" from each of the short sides, that means you will have two long lines. Turn the paper and score at 2 1/2" on one end. Then proceed to cut the sides out until you get a capital letter T. Go back to scoring, on the long 2 3/4" strip near the narrow end, score in at 1 3/4", at 5.5" and again at 7" from the outer edge. Turn the paper and score in 1/2" on each of the ends of the short side. At the top of the T you will see where you have scored a section of 1/2 x 1/2", trim these out as shown in the picture below. Also on that same section trim in 1/2" on both sides of the center strip where scored. This creates a flap. Take a 1 1/4" circle punch and punch out a circle centered in the middle of the 1 3/4 x 2 3/4 section of only one of the T's. Do not discard the circle that has been punched out.
Bend each of the scored lines in a mountain fold except the top one, bend it in the valley fold. Add strong adhesive to the four edges shown (they are the flaps for creating the box). I used 1/2" Sookwang adhesive.
In the photo below you can clearly see where I had you trim in 1/2" on each side to create the flaps. Remove the adhesive from this flap and attach it to the adjacent piece. Repeat on the other side. This will create the bottom of the box.
Then one side at a time remove the adhesive and attach to the adjacent piece. Do the same with the other side, this creates the back of the box.
You now should have a piece that looks like so.
Repeat these steps to create your second box.
Lay the flap with the circle punched out over the other flap and trace the circle with a pencil so that it lines up exactly. Lay your punch over the drawn circle and punch it out.
Cut out the following pieces of patterned paper:
2 - 1 3/4 x 2 1/2" (front of boxes)
2 - 2 1/2 x 3 1/2" (inside of boxes)
1 - 1 1/2 x 2 1/2" (top flap)
4 - 1 1/4" x 1 3/4" (sides of boxes)
Attach the pieces to your boxes centering them on all of the appropriate parts (except for the top flap).
With dotto adhesive (or any other temporary adhesive) adhere the two short edges onto the back of the top flap, centering it. This ensures you have your circle marked exactly where you want it with your paper centered.
Draw with a pencil the circle on the paper. Remove the paper from the back of the flap and rub off the temporary adhesive.
Line up the 1 3/8" circle punch over the drawn circle and punch it out.
Attach it to the one flap. You should now have two boxes as shown below.
Add a strong adhesive on the top side of the top flap that does not have the patterned paper on it.
Line it up and adhere the two boxes together, keeping the one with the patterned paper on top.
Top view
Time to decorate. Now to make a rosette, take a 1 x 12" strip of patterned paper and score it ever 1/4". Fold it in an accordian style with mountain and valley folds.
Use a strong adhesive to glue the two outer folds together. I used Crystal Effects. If you use Crystal Effects hold it in place for a minute or so as it is a liquid adhesive.
On one of the circles you punched out from the top flap add some Crystal Effects. Manipulate the cardstock to flatten into a circle and pinch it together in the center. Adhere it to the circle, hold for a minute or so.
You can see that I didn't get it exactly centered but it holds it together and you don't see that part later.
Using circle and scalloped circle nestabilities I created the front for my rosette. I stamped and sponged the circle and used matching patterned paper for the scallop circle.
Attach to the rosette.
Here is the front decoration for my nail care kit. I used the circle and scallop circle nestabilities again.
Lay the boxes over your nailpolish remover. Attach 1/2" ribbon around the boxes with a strong adhesive, again I used 1/2" Sookwang adhesive.
Adhere your decorations to the front and back of the boxes, I off center mine a little, I think it adds a nice touch and it gives a better view of what is inside.
I cut strips of matching patterned paper and wrapped a few chocolates to sit inside.
Here's the goodies I am sticking inside the boxes.
The finished product.
Remember to create your boxes based on the size of your nailpolish remover bottle, you want it to sit about 1/2" off the table surface. Another thing to check is the size of your cap to make sure you hole is big enough but not too big. If you need it bigger you will need to increase the size of the top flap to accommodate the change. Try it and share it with a good friend!
